Installation manual Octopus Duo CI

Title

Logozeile

Please read this manual carefully, it will help you to install and set up your Digital Devices product properly.
To download the latest drivers and updated manuals check out our website
www.digitaldevices.de
. For further contact details please browse to the end of this manual.

Note: We reserve the right for technical changes as well as changes in form, color and weight.

Safety instructions and hazard notices

The product is suited for use in PC-systems only.

Please read the following safety instructions carefully to avoid damage to persons or the product during use. Also obey the instructions in your PC manual.

Please provide the manual to people who carry out an upgrade or upgrade (also in case of resale).

Important safety instructions

  • Installation requires knowledge with PC systems and may only be carried out by experienced users and trained staff.
  • Never allow children to play with electrical appliances. They can not recognize hazards.

Disconnect your PC from the power supply before doing any work, and then wait a few minutes for all components to cool down before performing any work. There is a risk of electric shock when connecting to the power supply, which can be fatal.

  • The power plug must be accessible in order to allow disconnection from the power supply in case of danger.
  • Never bridge connections in the system or the power supply fuse, as there is a risk of electric shock.

Hazard information to work on your PC

  • Do not plug or unplug any cables when the PC is switched on (not even the antenna cable).
  • You should statically discharge prior to any work, for example by touching a grounded object.
  • Use only components and cables in perfect original condition. Defective devices and cables must be replaced.
  • Use the card only at the intended connections (PCI Express or data port) and do not apply force during installation
  • The card / module must not come into contact with moisture or chemical solvents. Cards / modules which come into contact with liquid are to be sorted out.
  • On no account use tools (e.g. screwdrivers) to reach hardly accessible places in the PC. Power supplies carry voltage even after being switched off, therefore there is a risk of (lethal) electric shock.
  • Small parts such as screws can cause short circuits and should therefore not be located inside the PC.
  • Do not use the card / module and PC outdoors. Cables for indoor use must not be used outdoors.In the event of problems, defects or questions, please contact your supplier.

Disclaimer of liability

The following points will result in the loss of liability, guarantee and warranty claims:

  • Use of defective or modified parts and cables. Or parts and cables which have come in contact with liquids
  • Failure to comply to safety instructions or installation by non-qualified persons
  • Use of non-approved replacement parts

Electromagnetic compatibility and disposal

  • The guidelines for electromagnetic compatibility must be adhered to when connecting the TV card / module.
  • Electrical components must be disposed properly and do not belong in the household refuse.

Product features

With the Octopus Duo CI buyers get a CI module combined with a Bridge. The integrated CI module is designed for different reception modes like Pay TV.

Additional tuners can be incorporated seamlessly due to Digital Devices' focus on modular design solutions.

Designed and produced in Germany in addition to proprietary support by the manufacturer ensure a continual advancement of many software products.
Particular emphasis has been placed on environmentally friendly Green IT with low energy consumption and without environmental hazardous components.

Technical data Octopus Duo CI


Identification

  • EAN: 4260217681003
  • Part No.: 092123

Product category

  • Bridge module with integrated CI module as the foundatiion for tuner expansion modules
  • Connections for expansion modules available (tuner, CI)

CI Specifications

  • Multi Transponder Decryption, bis zu vier Entschlüsselungen unterschiedlicher Kanäle von unterschiedlichen Transpondern möglich (unter Windows)

Tested CA modules

  • Mascom Alphacrypt Light + Easy TV
  • SMIT Irdeto/Cryptoworks
  • SMIT Viaccess with SRG
  • Technicrypt CW with ORF
  • SCM Cryptoworks

Standard connections

  • PCI Express (x1-x16)
  • 2x 20-pin data port for DuoFlex expansion modules (e.g. tuner and common interfaces)

Dimensions

  • H 115 mm, L 48 mm, D 16 mm

Power consumption

  • < 2 watts inc. consumption of CA module

Supported operating systems

  • Linux (Kernel 2.6.34 or higher)
  • Microsoft Windows® XP(SP3), 7, 8, 8.1, 10; (32/64 Bit)
  • Windows® Media Center

System requirements

  • Dual Core Intel® oder AMD® CPU
  • 512 MB RAM
  • 1x free PCIe port (x1 to x16)

Enviroment and safety

  • RoHS compliant
  • WEEE compliant
  • Manufactured and designed according to European ISO / DIN guidelines and environmental standards.

Scope of supply

  • Octopus Duo CI PCI Express card
  • Quick Install Guide
  • Manual (on CD)
  • Driver (on CD)
  • DD-TV Software (on CD)
  • Slot bracket full-profile

Initialization

Note: Make sure to follow the safety instructions in this manual and in the user manual of your PC.

Initial preparation

  • Carry out a backup prior to the installation process.
  • Switch off the PC and disconnect the power supply. Now other external cables can be disconnected.
  • Put the PC on a stable surface in order to access the backside easily.
  • Wait a few minutes until all parts have cooled down before opening your PC and continuing the installation process.

Note: To prevent an electrical short circuit, newly acquired equipment and cards should not be put into operation until they have reached the surrounding temperature.

  • Attach the slot bracket to the card or module if necessary and use the screws provided with the product.

Note: Depending on the measurements the card comes with two slot brackets (Full Profile and Low Profile). Slot brackets in various designs are available separately.

Installing the card

Note: Electrostatic Discharge (ESD) can damage internal components of the PC. Hence, you should discharge before working on the system, for example by touching a grounded object.

  • Open the housing as described in the operating instructions of your PC.
  • Locate a suitable PCIe slot and remove the slot cover.
  • Keep the TV card at the slot bracket and plug it vertically into a free PCI Express slot (x1-x16) until the TV card is locked into place firmly. Be careful not to damage any surrounding components.
  • Tighten the screws of the slot bracket until the card is fastened.
  • (Optional, when using a Cine-S2): Connect the power connector to your power supply if your LNB requires that (> 5 watts of power consumption). LNBs with a power consumption of up to 20 Watts can be utilized.
  • Close the housing
  • Reconnect any disconnected cables
  • Connect the antenna cable to an antenna input port of your TV card or to your tuner module
  • Finally, connect the power cord to the PC and turn it on.

Connection diagram Octopus Duo CI

Abb.:Digital Devices Octopus Duo CI Anschlüsse

Insert CA module

Insert the SmartCard of your PayTV provider into the CA module (CAM) and then slide the CAM into a free CI slot of the CI. The pressure is slightly increased shortly before the stop when the CAM is plugged in correctly. After the position is reached, the CAM can be pushed for approximately another 5mm into the CI.


CA modules can also be plugged in or unplugged during operation. Detection is done automatically without the need of restarting the PC.


Up to two CA-modules can be used.

insert cam

Driver installation

Driver installation on Windows PCs

Preparation:

  1. Start your web browser and go to www.digital-devices.com.
  2. Now click on "Downloads" and download the appropriate driver for your individual operating system.

Drivers are available for the following versions of Windows:

  • Microsoft Windows® XP (SP3), 7, 8, 8.1, 10, in 32 and 64 bits
  • Windows Media Center is fully supported.

Driver installation

Caution: When installing new drivers or programs, existing data can be overwritten or changed.
Hence, you should create a backup copy of your hard drive before proceeding with the installation.
Compensation claims for loss of data and resulting damages are excluded.

Note: For Windows® XP, please log in with a user account which has been granted administrator rights.

  1. Start the setup program by (double) clicking the downloaded file: "DigitalDevices DVB Driver X.msi".
  2. Now please follow the instructions on the screen.

Note: If you select an installation directory other than the suggested installation directory, the DD Control Center for managing the cards and modules can only be accessed from the installation directory and not from the control panel.

  1. After completing the installation, restart the computer.

Note: The message "The driver to be installed has not passed the test..." is no indication for a malfunctioning driver, but rather for a missing Microsoft signature.

The error message can be ignored, thus clicking the "Next" button.



After successful driver installation, three new entries are displayed in the Windows device manager (In case of additional modules installed more entries may appear).

The following image is an example of Windows® 10.


Driver installation on Linux

Current drivers are available here: https://github.com/DigitalDevices/dddvb/releases

In the following it is assumed Ubuntu/Debian, OpenSUSE, and Fedora Linux are being utilized. Other distributions may work in a similar way.

Installation of the components

Ubuntu/Debian:

sudo apt-get install mercurial build-essential libproc-processtable-perl linux-headers-$(uname -r)


OpenSUSE

sudo zypper install -t pattern devel-basis

sudo zypper install mercurial perl-Proc-ProcessTable kernel-devel kernel-source

Fedora:

sudo yum groupinstall "Development Tools" "Development Libraries"

sudo yum install mercurial perl-Proc-ProcessTable kernel-devel kernel-headers

 

Operation (execution in a console / terminal)

Download and unzip the current dddvb drivers

cd /usr/src

sudo wget https://github.com/DigitalDevices/dddvb/archive/0.9.36.tar.gz

sudo tar -xf 0.9.36.tar.gz


Build drivers

cd dddvb-0.9.36

sudo make


Installing modules

sudo make install


Specify the sequence for loading the modules

sudo mkdir -p /etc/depmod.d

echo 'search extra updates built-in' | sudo tee /etc/depmod.d/extra.conf


Announce the new modules and their dependencies to the system

sudo depmod -a


When using a Max S8, create the ddbridge.conf file

echo 'options ddbridge fmode=x' | sudo tee /etc/modprobe.d/ddbridge.conf

(Substitute X with mode of operation / fmode)

Note: If I2C timeouts occur, please disable MSI for ddbridge: echo 'options ddbridge fmode=x msi=0' | sudo tee /etc/modprobe.d/ddbridge.conf


Load driver

sudo modprobe ddbridge


Operating modes for the Max S8:

Fmode=0 4-tuner mode(Internal multiswitch deactivated)

fmode=1 Quad-LNB / normal outputs of the multiswitch

Fmode=2 Quattro-LNB / cascade outputs of the multiswitch

fmode=3 Unicable or JESS LNB / Unicable-exit of the multiswitches


Settings in the Linux driver

Set the following ddbridge parameters for fmode:

  • fmode = 0
  • fmode = 1
  • fmode = 2
  • fmode = 3

Demod 0 & 4 at input 1

Demod 1 & 5 at input 2, etc.


The input for each frontend can be changed using: ioct DTV_INPUT All cables are connected via a Quad LNB

All cables are connected via a quattro LNB or multiswitch cascade output: Input 1=VL, 2=HL, 3=VH, 4=HH

All demods are connected to Input 1 and send JESS or SCR (Single Cable Routing) commands from the application

Digital Devices Control Center

Version 3 (15.09.2018)

The Digital Devices Control Center is included in driver version 2.7.0.108 or higher and is used to manage Digital Devices DVB-products on Windows systems. Network tuner configurations can be set via WebInterface or Octopus Cast Tool.

Functions

The following settings and functions can be adjusted in the DD Control Center:

  • Setting operating mode (Unicable® system)
  • Assigning reception mode (DVB-S/S2 as well as T/T2 and C/C2)
  • Hardware information and diagnostic capabilities (Tunerlog, signal strength, temperature)
  • Firmware updates
  • Assign tuner to CI (if available)
  • Access to CAM menus (if available)

Accessing the DD Control Center

Since driver version 3 the DD Control Center is integrated into the Windows Start menu and can be accessed there (up to version 2 it was accessed via the control panel).

For certain functions (adjusting driver settings) it may be necessary to run the application as an administrator.

Hardware

Connected hardware is displayed under Devices. For each standard card, a menu item is created for selection.
If the card is equipped with expansion ports, those are displayed in the main screen, as well as the DuoFlex modules connected to them.

For diagnostic purposes, hardware data is available, which is presented in greater detail within the Diagnostics + maintenance section.

If installed cards or modules are not displayed properly, it must be checked whether they are connected correctly or not.

Setup

CI setup, assigning a CI and tuner

In order for a CI or CAM to decrypt received TV signals, it must be assigned to one or more tuners.
In the Tasks-Common Interface Assignment menu, the built-in tuners and CI modules are displayed as a matrix in which the assignment can be determined by activating the checkbox(s).

  • If the CAM supports Multi-Transponder Decryption (MTD) technology, it can be assigned to up to four tuners, and the CAM will automatically run in MTD mode. If only one tuner is assigned, the CAM will run in STD mode (Single Transponder Decryption).
  • Multiple CIs can be assigned to a single tuner, allowing to use different pay-TV providers with the same tuner (CI cascading)

Assignments after hardware configuration change

If CI modules are removed or added, the assignment process must be repeated and is maybe even necessary after driver updates.

The Delete all button will reset all CI settings.

Diagnosis

The CI assignment can be viewed in the Devices menu for cards and modules.

Adjust CAM settings

In the CAM menu, the menus of installed CAM modules can be accessed and individual settings can be made. The selection of CAMs is carried out in the menu.

The main window shows all menu items of the CAM after a short time.
Note: This is the CAM menu provided by the manufacturer, the Digital Devices Control Center is just the display medium


Tip:

If your TV software does not provide access to the CAM menu, you can leave it open in the background and then use the DD Control Center.

This allows, for example, to view current status messages or accessing debugging information (function depends on deployed CAM).

Adjusting CI bitrate (Octopus CI S2 Pro and Octopus Duo CI)

For integrated CIs of Octopus CI S2 Pro and Octopus Duo CI, the bitrate can be adjusted in the devices menu in case decryption errors occur.

Differences between Multi Transponder Decryption (MTD) and Single Transponder Decryption (STD)

The Digital Devices TV software is included in your TV card package and is compatible with various applications.

Digital Devices TV

The digital devices TV software is included in your TV card.

In addition to the internal DVB-S, DVB-C and DVB-C cards you can also integrate networks such as the Octopus NET.

The latest version can be downloaded from: Digital Devices ? DD-TV Download

The application manual is available from: DDTV-Handbuch

Third party TV software providers:

The TV card supports many TV applications like Microsoft Windows® MediaCenter 7/8, DVBViewer, Media Portal, Gen2VDR, MythTV

Instructions for various applications are available on our website www.digital-devices.de.

Technichal drawing Octopus Duo CI

Extensions

Digital Devices TV cards and modules can be expanded and combined easily thanks to the modular design of Digital Devices solutions.

Each DuoFlex module can be connected to any TV card or bridge via an expansion connector.

Even cards without expansion connectors can be integrated since the PCIe system bus is able to establish a connection.

In either case additional modules are seamlessly integrated into the Digital Devices Control Center.

Erweiterungsmöglichkeiten einer Octopus Duo CI

Various combinations of Digital Devices DVB components with an Octopus-Bridge are possible. (A maximum of 4 components can be connected).


DD Octopus DuoCI Kombinationen (horizontal)

Slot brackets

Accessories for various combinations are available and can be obtained from Digital Devices.

The following figure illustrates examples of slot brackets and power connections.

Sample configuration shown: Digital Devices Cine S2 v7 with a DuoFlex S2 v4 expansion module on a combined slot bracket K (available as accessory)

Installation of a Duoflex expansion module (tuner or CI)

Preparation, notes

  • Carry out a backup prior to the conversion
  • Switch off the PC and disconnect the power supply. Now other external cables can be disconnected.
  • Put the PC on a stable surface in order to access the backside easily.
  • Wait a few minutes until all parts have cooled down before opening your PC and continuing the installation process.
    Note: To prevent an electrical short circuit, newly acquired equipment and cards should not be put into operation until they have reached the surrounding temperature.
    Note: Electrostatic Discharge (ESD) can damage internal components of the PC. Hence, you should discharge before working on the system, for example by touching a grounded object.
  • Attach the slot bracket to the card or module if necessary and use the screws provided with the product.
    Note: Depending on the measurements the card comes with two slot brackets (Full Profile and Low Profile). Slot brackets in various designs are available separately.

Installing the expansion module

  • Open the housing as described in the operating instructions of your PC
  • Locate a suitable slot and remove the slot bracket
  • Insert the module into the slot vertically and tighten the screws of the slot bracket until it is fastened. Be careful not to damage any surrounding components.
  • Connect the expansion module to the expansion connectors of your main card (Cine series or Octopus series) utilizing the supplied ribbon cable TAB sequence ascending.

    Note 1: Make sure to use only original Digital Devices data cables for connections. For connections with tuner modules, cables with a ferrite core should be used.

    Note 2: Make sure to connect the cable properly if dealing with an older DuoFlex module. The red wire of the cable must be pin 1 on the module or on the card (red wire at the bottom). For newer types, the connections and cables are protected against polarity reversal.

  • Link the power supply of your module with a connector from your power adapter or the connector of your card (if available)
  • Close the housing
  • Reconnect any disconnected cables
  • Connect the antenna cable to an antenna input port of your TV-card or to your tuner module
  • Finally, connect the power cord to the PC and turn it on

The module is managed like your existing card or module within the Digital Devices Control Center. The integration is seamless, you do not need to do anything.

Expansion connectors (Datenports, Tabs) der Octopus Duo CI

Datenports Tabs Octopus Duo Ci

Notes on data connection

If multiple modules are utilized, connected tuner modules are identified in the system as follows, depending on the TAB used:

  • TAB 1 to Octopus series -> Tuner 1 & 2
  • TAB 2 to Cine or Octopus series -> Tuner 3 & 4
  • TAB 3 to Cine or Octopus series -> Tuner 5 & 6
  • TAB 4 to Cine or Octopus series -> Tuner 7 & 8

Make sure that tuner extension modules are connected to smaller TABs of the Cine or Octopus series in terms of numeration than the DuoFlex CI.

Troubleshooting

Please consider the following advice, once a problem regarding your card occurs. Please access our knowledge base for more information and assistance at: http://support.digital-devices.de/

Basic prerequisites / testing for errors

Turn off the PC and disconnect the power cord before carrying out any checks.

Now perform the following checks:
  • Are all cables and connectors properly connected?
  • Is the card firmly plugged into the PCIe slot?

If the card is not recognized by the system, please try another PCI Express slot. Since some motherboards don't recognize cards plugged into a PCIe X16 slot properly. Utilizing the X4 or X1 slot should be considered.

  • Make sure using original equipment only. Do not interchange cables from different devices, even though they appear identical. They may differ in pin configuration.
  • Does the antenna provide adequate antenna power?
  • Make sure to implement a minimum distance of one meter to high-frequency and magnetic interference sources (TV set, mobile phone, speaker boxes, etc.).
Turn the PC back on and carry out the following checks:
  • Does the card show up in the device manager or in case of a Windows PC in the Digital Devices control Center?
  • Inside BIOS, "PCI Express overclocking" should be set to 100 and not into "auto" mode.
  • Does the DD Control Center or your application display a signal?
  • Does the problem occur in one application only? Try it out in Digital Devices TV as well.
  • Is the installed driver up-to-date? Does the problem still occur when a different one is used?
  • Did you install the required codecs for playback on your system? Disable DXVA if block graphics occur with HD stations.

Prüfungen und Hinweise zur Fehlerbehebung bei Verwendung eines CI-Moduls

  • Sind nur verschlüsselte Sender gestört oder auch unverschlüsselte?
  • Steckt das CAM richtig im CI und ist dieses korrekt angeschlossen?
  • Besteht das Problem auch, wenn Sie die CI-Zuweisung im DD Control Center entfernen und das CAM herausziehen?
  • Wird mit zugewiesenem CI kein Signal mehr angezeigt, ohne aber problemlos, könnte Ihr CAM defekt sein. Testen Sie es in einem anderen Gerät.*
  • Ist Ihre Smartcard freigeschaltet? Können die verschlüsselten Sender mit einem anderen Gerät/CAM entschlüsselt werden, z.B. einem Receiver?
  • Wenn das CAM in einem anderen Gerät einwandfrei funktioniert, stellen Sie bitte im BIOS/UEFI die PCIe-Busfrequenz auf 100 ein (Häufige Bezeichnungen sind ?PCIe Frequency" "PCIe Overclocking" "BCLK/PEG Frequency?).

Hintergrund: Das CI hat eine bestimmte Taktung. Hat PCIe Bus höhere, kommen die Daten zu schnell beim CI an und es wird kein Sender angezeigt.

Imprint & contact

Inquiries from OEM and industrial customers

Digital Devices GmbH

Eckhard Stock

Mittelstrasse 5/5A

12529 Berlin Schönefeld

Germany

Company registration number: HRB 14007 CB in Cottbus

VAT Id No.: DE 266 587 135

Phone

Management +49 (0) 89-43759192

Customer Hotline +49 (0) 2065-6989930

E-Mail

sales@digitaldevices.de

Inquiries from distributors, retailers and end users

Digital Devices Distribution GmbH

Norbert Auge

An der Geis 67

D-47228 Duisburg

Company registration number: HRB 21725 in Duisburg

VAT Id No.: DE 269 963 931

Phone

Head office +49 (0) 2065-6989930

Fax +49 (0) 2065-6989999

E-Mail Shop

shop@digital-devices.de

Product support and advice

Support form: Produktsupport Digital Devices

Phone: +49 (0)2065 - 6989930 (Mon-Fri 09:00 - 18:00 Uhr)

Digital Devices product portfolio

The Cine series TV cards are the basic products for various Digital Devices solutions. Our Dual Tuners can easily be enhanced with different tuner- and CI-modules to accommodate multiple variations.

Whereas the Octopus series is aimed at the characteristic demands of specific TV tuner environments.

Combinations with CI expansions as well as external solutions are an example of our flexible modular design within the DVB product range.

The DuoFlex series complements the Cine series by incorporating various expansion modules (Tuner, CI) via ribbon cable (No additional PCIe slot required).

Explore the world of Digital Devices at www.digitaldevices.de !